Showing posts with label Murphy's Oil Soap. Show all posts
Showing posts with label Murphy's Oil Soap. Show all posts

Saturday, August 8, 2020

Basic Furniture Refinishing

QUESTION: I have a 1930's silky oak drop-door desk that has been in our shed for about 20 years.
It has seen a few cyclones and had a lot of weathering and the doors are off and knobs missing.
This desk holds special memories for me as a young child watching my dad working at it. I’d like to refinish it but have no idea where to begin. How hard would it be for a beginner like me to refinish it?

ANSWER: Your desk sounds like the ideal piece of furniture on which to learn about refinishing furniture. For many beginners, refinishing seems easy, but it’s far from it. First you need to decide if the piece needs to be completely refinished or the original finish preserved. Your desk sounds like it may fall somewhere in between.



It’s only been within the last 20 years or so that refinishing products have appeared that make the job less intimidating. However, most people think you have to strip off all the old finish before applying a new one. That all depends on the condition of the piece.

You piece sounds like it’s been through some tough times. Before you do anything, you need to evaluate it. Has the finish been mostly removed by weathering or is it spotty. If it’s the former, then you’ll need to sand it following the grain of the wood with fine to medium grade sandpaper. If it’s the latter, you may be able to just clean it up and apply a new coat of varnish. With refinishing, a little effort goes a long way. The nearer you can keep your desk to its original condition, the better.

Let’s assume the worst. If the finish has mostly been removed by weathering, you’ll need to remove what remains with a good varnish remover. Be sure to buy one that’s water soluble. Even though this takes longer to achieve the results you want, the fumes are mild and cleanup is easy. When using a remover, always brush it on with the grain of the wood. Do a little section at a time, turning the piece on end if necessary to make it easier to apply the remover. Scrap it off with a putty knife, and be sure to have a roll of paper towels handy to wipe up the excess and stripped varnish or paint.

After you’ve completely stripped your desk of its finish, lightly sand it with fine sandpaper. Wrap the sandpaper around a wooden block for support and sand with the wood grain. Be careful not to over sand----just enough to smooth the surface. After you’re finished sanding, wipe the desk with a damp cloth to remove all the dust. Do not get the wood wet.

Once you have prepared your desk for its new finish, let it rest for a day to make sure the surface is thoroughly dry. Dust it off with a dry cloth to make sure it’s clean, then begin to brush on a new finish using a soft-bristle brush and a furniture finish called tung or Chinese oil. Several manufacturers make this, including Formbys, and you should be able to buy it at your local hardware or home center. Apply the tung oil or a piece of white tube sock or other soft cotton material going with the grain of the wood.. The first coat will soak into the newly stripped wood. Let it dry 24 hours, then sand lightly with fine sandpaper. Dust it with a damp cloth again and let dry. Apply a second coat of the tung oil and repeat the process, except this time rub it with 0000 steel wool after it dries. Dust off again and apply a third and final coat of tung oil, but don’t rub with the steel wool this time.



The advantage to using tung oil is its rapid drying capability. Though it will feel dry to the touch in an hour or so, be sure to let it thoroughly dry for 24 hours. And don’t apply it on a humid or rainy day. And here's a tip: Wrap your application cloth in plastic wrap or put it into a Zip-Loc sandwich bag and place it in your freezer. Take it out 30 minutes before you're ready to apply another coat, and it will be ready for you.

Be sure to tune in next week to learn about preserving the finish of a piece of furniture that isn’t in such bad shape.

To read more articles on antiques, please visit the Antiques Articles section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the over 30,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about  world's fairs in the 2020 Summer Edition, online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques and More Collection on Facebook.










Tuesday, January 22, 2019

An Ounce of Prevention is Worth a Pound of Cure



QUESTION: What’s the best way to maintain antique furniture? When I see pieces at antique shows, they always look so beautiful. Is there some trick to making them look that way? Can you tell me the best way to maintain the pieces I have? While I have some older ones from the early 19th century, most are from the mid to late 19th century.

ANSWER: You’ve asked about two different procedures. The first is all about restoration while the second is about conservation.

Generally, restoring pieces made before 1830 affects their value. If a piece is more than 60 percent restored, it drastically loses value. Refinishing these early pieces destroys their patina. On the other hand, pieces made after 1830 usually benefit from restoration. The 60-percent rule doesn’t apply to them.




Restoration can range from minor repairs to a complete professional refinishing. With improvements in materials and finishes, a person can do some simple refinishing at home. However, for more complex work, especially when a piece may have several layers of old paint that have to be removed, it’s a good idea to invest in the work of a professional furniture restorer.

Before attempting to refinish a piece of antique furniture, assess it’s overall condition. If the piece just looks dull and dingy, it’s possible it may just need a thorough cleaning. Cleaning wood can do wonders for it.

If there’s oily dirt or grease, such as may get on pieces in a kitchen, remove it with an old washcloth, soaked in a mild dish detergent and water solution and wrung out. Work on small area at a time and dry it immediately with a soft cloth. Always avoid using too much liquid directly on a piece’s surface.

An alternative is to use Murphy’s Oil Soap in spray form. Spray a little on the wood and wipe with a damp washcloth. For really grimy surfaces, use #0000 steel wool and Murphy’s, then wipe with a wet washcloth, and dry. Allow the piece to dry thoroughly for 24 hours before waxing. Wipe the surface with #0000 fine steel wool until smooth.

After a piece of furniture is cleaned, it can be freshened up using Wood Sheen, a rubbing oil stain and finish made by Minwax that combines tung oil with a coloring agent, available at most hardware stores and home centers. This product comes in a variety of wood stain colors to match most types of wood.  tra fine (four zero) steel wool. Wipe the surface again with a damp cloth. Apply a thin coat of Wood Sheen using an old sock and let it dry for an hour or two. Do not do this more than once every year or so.

An alternative to using Wood Sheen is to wax it with Minwax paste wax. This is a petroleum-based product that comes in both natural and dark shades for light and dark-stained furniture, respectively. The hard surface it produces can be dusted more easily and without the danger of scratching because its smoother. Waxing once or twice a year is sufficient for table tops and chair arms. For less used areas of furniture, such as chair legs and case pieces, wax only every four years.

Conservation of antique furniture is all about maintenance and keeping it clean. Avoid using any of the popular spray dusting helpers. These tend to leave a nasty buildup on furniture that’s hard to remove later on. Instead, use a soft cloth to gently wipe away the dust. You can also slightly dampen the cloth with liquid glass cleaner.

Avoid using any of the popular oil-based liquid furniture polishers. These leave an oily residue that attracts dust. Lemon oil is one of the worst because it doesn’t sink into the wood like commonly thought but lays on the surface acting as a dust magnet.

Be extra careful when cleaning any wood that has been gilded. The gilt is usually applied with a water-soluble adhesive which can be removed by detergent cleaners. To clean uneven or carved surfaces, use a soft-bristled brush or your vacuum cleaner with the brush attachment. Be careful not to hit the furniture in any way with the vacuum cleaner, itself.

Do not use feather dusters. They move the dust around and can scratch the surface.

Before using any cleaner on a piece’s surface, test an inconspicuous area towards the back first.

Try not to polish hardware while it’s attached to the furniture. The polish will damage the furniture’s finish. Instead, remove the hardware and polish separately, being sure to rinse or wipe it thoroughly before reattaching it to your pieces. If hardware cannot be removed, be sure to mask it from the furniture’s surface to prevent damage. For ornate hardware, use a cotton swab dipped in the detergent solution.

Do not polish ormolu, which really isn’t brass but bronze. Instead, wash it with a soft cloth soaked with a mild dish detergent.

If mold or mildew forms on a piece of antique furniture, dampen a soft cloth with a very mild bleach solution (two tablespoons of bleach to a quart of water) and wipe the affected area. Dry immediately with a soft cloth, then wax as stated above.

Heat dries out the wood of antique furniture, loosening joints. An interior should be kept at a comfortable level but not excessively hot in the winter. If the temperature must be kept higher, put pans of water around to humidify the air or use a humidifier. The air will be healthier, also.

To read more articles on antiques, please visit the Antiques Article section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 18,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about religious antiques in the special 2018 Holiday Edition, "The Art of the Sacred," online now.

Wednesday, February 28, 2018

Giving New Life Through Restoration



QUESTION: For years I also collected antiquities. Now I have a particular passion of writing boxes or old English boxes. I enjoy to restore by myself. I beg to ask for an opinion. I attach here two photos. On the lid, at the corners, something is missing! Do you think the angles were made of brass? Or in wood ... or mother of pearl? I doubt it because the thickness is a lot (about 3 mm.) Then I had never seen the brass corners that did not go vertically.

ANSWER: The corners on your box would have been brass, so if you can find someone to make these for you, they should be easy to replace. Be sure to glue them with a strong glue. Box makers usually used brass on the corners of better boxes to protect them while traveling. Victorians took writing and other types of boxes along on long trips so that they could communicate to their friends and family back home. It’s not unusual to find boxes from this time period in poor condition. Restoring them is not as difficult as doing furniture but can be challenging.

Antique boxes acted as portable storage workhorses for past generations. They served a variety of purposes from document boxes in which to keep valuable papers to writing boxes for correspondence to dressing boxes for grooming while traveling to tea caddies for storing precious tea. Victorians, in particular, loved boxes and people from all classes used them.

Unfortunately, people handled boxes a lot, so most antique ones aren’t in the greatest shape. Some boxes may have sat on a table in front of a window in the sunlight and became faded over time while others suffered from neglect.

A good example is an Indian sadeli mosaic-covered writing box that outlived its usefulness. Someone decided that instead of tossing it out, they would give it to their children to play with. The children drew all over the beautiful mosaic with crayons and someone did a bad job of pasting a piece of chartreuse felt over the writing surface on the inside. Needless to say, this restoration wasn’t a walk in the park.

Unlike antique furniture made before 1830, many antique boxes will benefit greatly with even modest restoration. And since they’re not large, it doesn’t take a lot of materials or time to restore them.

Antique boxes are valuable because they’re antique and looking old isn’t bad. And while restoring a box may make it look better, it may reduce its historical value. Boxes from the 18th century should only be restored by a professional restoration expert. In most cases, they need to be conserved, that is the deterioration of the box should be halted. Restoration is a more radical solution and often includes refinishing the wood and replacing metal parts. So the question to be asked is whether the box is in bad enough shape to render it less valuable than its being restored?












While restoration usually begins with reviving the wood of the box’s body, it also takes in exterior decorations made of ivory, tortoiseshell, and mother-of-pearl. These materials are all fragile and should be checked for cracks, abrasions, and chips. Metal ornamentation may be missing, dented or creased, or it may just need polishing. Veneers and inlay are much more difficult to repair and may require professional assistance.

Antique boxes also contain small and sometimes specialized hinges and locks that must also be examined for repair, restoration, or replacement. Finding replacements can be a real challenge since many of these may have been made for a particular box.

But minor conservation can do wonders for an antique box. First, tighten any loose screws and gently tap in any loose nails. Repair loose joints with wood glue. Finally, clean the box with a soft lint-free cloth dampened with Murphy’s Oil Soap solution. Do a small area at a time and use another lint-free cloth to dry it. After letting the box dry thoroughly for 24 hours, give it two coats of Minwax past wax to protect the exterior. Follow the directions on the can.




Dust the interior of the box with a soft shaving brush. If the wood is bare, as with some inner areas of the box, switch to a solvent-based cleaner. Use a toothbrush or toothpick to clean out any crevices. If this has markedly improved the box’s appearance then it may be a good time to stop.

To read more articles on antiques, please visit my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 18,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about the Victorians in the Winter 2018 Edition, "All Things Victorian," online now. 



Monday, June 10, 2013

Whistle While You Wax



QUESTION: I have quite a few old pieces of furniture, some of which are antiques. I’m never sure what to use to clean and polish them. Can you offer any advice?

ANSWER: You’re not alone. Many people don’t know what type of cleaners and polishers are appropriate for antiques and end up using the wrong thing.

Before you can figure out what type of cleaner and polisher to use on your furniture, you first have to know what sort of finish the maker used on it. The most common finishes found on antique furniture are waxes, oils, shellacs, and varnishes. Not only do these finishes bring out the beauty of the wood's grain and color, but they also protect the wood from moisture and heat changes that can cause shrinking, swelling, crazing, and cracking. Finishes seal the wood pores against dirt and grime, too.

But over the years, wooden furniture dries out and shrinks or expands or warps from too much moisture. Older antiques sat in rooms heated only by a fireplace. If they sat too close to the fire, they dried out—too far away from it, they tended to warp.

In order for a finish to protect the wood, you have to protect the finish. This can be done by cleaning and polishing the finish with either a wax or an oil.

Cleaning furniture is a simple process. Using a solution of Murphy’s Oil Soap or the spray version of it, apply some to a well-wrung-out old washcloth. Rub a small area of the piece at a time and immediately dry it with either paper towels or an old towel. If the piece is particularly grimy, you may have to wash it several times. Be sure not to get the wood too wet and dry each area immediately. After you finish cleaning, let the piece dry thoroughly for 24 hours. For a really bad piece, you can also use one of those green scrubby squares. But don’t rub too hard because you may rub off the finish.

Once your piece is dry, it’s time to apply a new protective coating. The preferred method of protection is a wax since they’re easy to apply and leave a brilliant shine. The best waxes to use are those in paste form. Stay away from Pledge or other so-called spray cleaners and waxes. They apply a film to the surface of furniture which attracts dust like a magnet. Instead, look for products that contain Carnuba wax, a natural substance from a palm tree native to Brazil that’s durable and produces a glossy shine when rubbed vigorously.

Another reliable polish is beeswax, which has been around for many years. A variety of paste and liquid polishes containing beeswax are available.

Minwax Paste Wax, made from petroleum products, is a third alternative. It produces a durable hard shine that lasts up to a year. The more coats you apply, the more waterproof the surface becomes.

Oils such as Tung and linseed have been used for centuries to preserve and polish furniture finishes. They're often mixed with absorption promoters, so they actually sink into the wood pores rather than remaining on top as waxes do. Oils leave a lustrous shine that's softer than a glossy wax shine, and they provide good protection against moisture. However, they do tend to darken the wood slightly over time.

Regardless of which cleaner/polisher you choose—wax, oil, or feeder—always use the same type on a particular piece of furniture. Finish surfaces that are accustomed to one type of cleaner/polisher won't accept another type. For example, an oil applied to a finish that was previously waxed will remain on the wood surface and won't soak in.

How often you need to clean and polish your antiques will depend on a number of variables, such as the type of heating and cooling system in your home, the geographical location, how you use your antiques, and the type of cleaner/polisher you're using.

Generally, you’ll need to apply a paste wax every month or so. To tell if your piece needs another layer of paste wax, buff the old finish with a soft cloth. If this polishing fails to restore shine and smoothness to the finish, it's time for a new coat of wax.

For more specific details on cleaning, check out my previous blog from August 15, 2011.

Monday, August 15, 2011

Preserving Antique Furniture



Some pieces of furniture, especially those constructed of harder woods, such as walnut, mahogany, maple, oak, or cherry, may only need to have their surface finish preserved. In the case of furniture made of these woods, there may be enough of the original finish left to restore the piece rather than refinish it.

Before doing anything, study your piece. Is the finish pretty much intact? Does the piece have a nice patina? Is the piece more than 100 years old? If you answered yes to even one of these questions, then you should do your best to preserve the finish of your piece.

The first step to preservation is cleaning. Furniture gets dirty, even grimy over time. Before you can apply a new finish, you need to get rid of all the accumulated dirt and grease that often make it difficult to tell what kind of wood the piece of furniture is made of. Grime can also hide the fine lines of inlay and marquetry. Believe it or not, using lemon oil, a popular furniture polish, can do more harm than good. Since its made of a light petroleum oil and some paraffin wax, the wood doesn’t absorb it. Instead, it acts as a surface dust catcher.

One of the best products for cleaning wood, especially furniture, is Murphy’s Oil Soap. Today, it’s also in a spray bottle, but in case you can’t find it that way, you can make your own cleaning solution by mixing a capful of Murphy’s in a spray bottle of water. For this, you can use any empty spray cleaner bottle, as long as you wash it out thoroughly first. Since water will loosen any glued joint, and also tends to raise the grain of the wood, you don’t’ want to use very much. An old washcloth will do quite well for cleaning.

Spray the Murphy’s on a damp washcloth and then rub it on the surface of the furniture. Rinse the cloth when it gets to dirty. Have a second wet, but wrung out, washcloth ready to wipe off the Murphy’s Oil solution, wringing the cloth nearly dry after every few wipes. You can also use a green scruby cloth, sold in Dollar Stores, if there’s hard to remove grime. A stiff-bristle brush will allow you to get the dirt out of carved and turned areas. The secret is to clean only a small area at a time–one leg of a chair, one part of a chest, and so on. After you clean an area, wipe it dry with an old face towel. Be sure to wash out all your cloths or use others as you progress, especially on a large piece of furniture. After you have finished cleaning your piece of furniture, give it a final wipe with a clean cotton rag and set it aside to dry for 24 hours.

Now you’re ready to apply a new finish. You can either use plain tung oil (see last week’s blog) or a product like Minwax® Water-Based WoodSheen® which is a water-soluble mixture of furniture finish and stain that comes in six colors. For a piece that’s got lots of scratches or marks, it’s best to choose a stain color that complements the wood’s original finish.

The final step is polishing the entire piece using a prepared wax like Minwax, which comes in light and dark varieties. Obviously, use the light for woods like oak or cherry and the dark for woods like walnut or mahogany. Apply the wax with a piece of soft cotton cloth like an old athletic sock and after 30 minutes, polish the surface with an old face towel. One coat should do it, but for tabletops, apply two coats of wax.

Rub off the first coat with 0000 steel wool, then apply the second and polish with the towel. The more coats of wax you apply, the more water resistant the top will become. A light polishing once or twice a year will keep your piece in great condition.

There are no short cuts or time savers to this entire process. The work can be slow and at times tedious, but the results are worth it.