Basic Furniture Refinishing

QUESTION: I have a 1930's silky oak drop-door desk that has been in our shed for about 20 years.
It has seen a few cyclones and had a lot of weathering and the doors are off and knobs missing.
This desk holds special memories for me as a young child watching my dad working at it. I’d like to refinish it but have no idea where to begin. How hard would it be for a beginner like me to refinish it?

ANSWER: Your desk sounds like the ideal piece of furniture on which to learn about refinishing furniture. For many beginners, refinishing seems easy, but it’s far from it. First you need to decide if the piece needs to be completely refinished or the original finish preserved. Your desk sounds like it may fall somewhere in between.



It’s only been within the last 20 years or so that refinishing products have appeared that make the job less intimidating. However, most people think you have to strip off all the old finish before applying a new one. That all depends on the condition of the piece.

You piece sounds like it’s been through some tough times. Before you do anything, you need to evaluate it. Has the finish been mostly removed by weathering or is it spotty. If it’s the former, then you’ll need to sand it following the grain of the wood with fine to medium grade sandpaper. If it’s the latter, you may be able to just clean it up and apply a new coat of varnish. With refinishing, a little effort goes a long way. The nearer you can keep your desk to its original condition, the better.

Let’s assume the worst. If the finish has mostly been removed by weathering, you’ll need to remove what remains with a good varnish remover. Be sure to buy one that’s water soluble. Even though this takes longer to achieve the results you want, the fumes are mild and cleanup is easy. When using a remover, always brush it on with the grain of the wood. Do a little section at a time, turning the piece on end if necessary to make it easier to apply the remover. Scrap it off with a putty knife, and be sure to have a roll of paper towels handy to wipe up the excess and stripped varnish or paint.

After you’ve completely stripped your desk of its finish, lightly sand it with fine sandpaper. Wrap the sandpaper around a wooden block for support and sand with the wood grain. Be careful not to over sand----just enough to smooth the surface. After you’re finished sanding, wipe the desk with a damp cloth to remove all the dust. Do not get the wood wet.

Once you have prepared your desk for its new finish, let it rest for a day to make sure the surface is thoroughly dry. Dust it off with a dry cloth to make sure it’s clean, then begin to brush on a new finish using a soft-bristle brush and a furniture finish called tung or Chinese oil. Several manufacturers make this, including Formbys, and you should be able to buy it at your local hardware or home center. Apply the tung oil or a piece of white tube sock or other soft cotton material going with the grain of the wood.. The first coat will soak into the newly stripped wood. Let it dry 24 hours, then sand lightly with fine sandpaper. Dust it with a damp cloth again and let dry. Apply a second coat of the tung oil and repeat the process, except this time rub it with 0000 steel wool after it dries. Dust off again and apply a third and final coat of tung oil, but don’t rub with the steel wool this time.



The advantage to using tung oil is its rapid drying capability. Though it will feel dry to the touch in an hour or so, be sure to let it thoroughly dry for 24 hours. And don’t apply it on a humid or rainy day. And here's a tip: Wrap your application cloth in plastic wrap or put it into a Zip-Loc sandwich bag and place it in your freezer. Take it out 30 minutes before you're ready to apply another coat, and it will be ready for you.

Be sure to tune in next week to learn about preserving the finish of a piece of furniture that isn’t in such bad shape.

To read more articles on antiques, please visit the Antiques Articles section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the over 30,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about  world's fairs in the 2020 Summer Edition, online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques and More Collection on Facebook.

Locating Parts for Antique Furniture

QUESTION: I have a Chippendale mahogany bookcase/secretary that is missing a finial. Do you have any idea where I can locate one?

ANSWER: Finding parts for pieces of antique furniture can be a quest in itself. But before you decide to restore a piece, you first have to know how old it is. A piece of furniture dating before 1830 is considered a fine antique. As such, it has special rules for restoration. First, you cannot replace more than 60 percent of it without it being declassified as an antique. Replacing anything on it will definitely lower the value. In fact, doing any sort of restoration usually hurts the value, unless it’s to restore the integrity of the piece.

Restoring furniture made after 1830 is another matter. A piece must be at least 60 percent original to have any value. If more has been done to it, then it's just another piece of used furniture.

As time goes on, even pieces dating from the mid-19th century will be scrutinized closer when it comes to restoration. However, generally the fine antique crowd tends to avoid anything Victorian, looking upon it as used furniture. Replacing parts and restoring a piece of Victorian furniture can actually enhance its value. But the replacement has to be of the finest quality and the restoration done right.

The date when this bookcase/secretary was made wasn’t specified. If it were an authentic 18th-century Chippendale piece, replacing that finial would have to be done by a professional cabinetmaker and restorer. This could cost several thousand dollars, but when the piece may be worth half a million in the first place, that’s a drop in the antique bucket. The cabinetmaker or joiner would have to hand-carve the missing finial to create an exact match to the original.

If—and that’s a BIG if—a replacement could be found from an identical bookcase/secretary, that would also work. But since 18th-century cabinetmakers all customized details like finials on their pieces, the chance of finding one is a million to one. The only way to make sure is to find a bookcase/secretary from the same cabinetmaker that’s beyond restoration and use it for parts.

On the other hand, if the piece were from a later period, which is probably is, it may be possible to find a finial floating around in a antique or junk shop. But you can’t just go to a home center and pick one off the shelf.

The first place to start looking is in antique shops that specialize in selling furniture. This could take years of browsing. But parts have been known to service in the least possible places.

You can also turn to a cabinetmaker who specializes in making replacement parts for furniture. This, again, could cost a bit since each part has to be handcrafted and that takes time.

Finally, there area a number of places on the Internet to find replacement parts. A lot of them sell mostly replacement hardware, but some, like antique furniture repair and refinishing companies, do make parts to order. McLean’s Refinishing, of Watkinsville, Georgia, stocks old furniture parts and has access to reproduction and replacement parts.

To read more articles on antiques, please visit the Antiques Article section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 24,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about antique clocks in the Fall 2019 Edition, "It's That Time Again," online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques & More Collection on Facebook.