Keeping the Railroads on Time

 

QUESTION: My grandfather worked as a conductor on the Pennsylvania Railroad. When he died some years ago, I inherited his pocket watch. For a long time, I thought it was just another old pocket watch. Then a friend, who’s father was a watch repairman, told me it was a special kind of pocket watch—a railroad pocket watch. Other than that, he didn’t know why it was so special. Can you give me some insight into antique and vintage railroad watches?

ANSWER: The answer to your question goes back to the last decade of the 19th century. On April 19, 1891, a train engineer's watch stopped for four minutes and then started again. This temporary mechanical failure resulted in a train wreck that killed nine people in Kipton, Ohio. The railroads set up a commission to create new standards for the railroad pocket watch, to be used by all railroads.

A railroad grade pocket watch was a watch that a particular railroad approved for use by its engineers and conductors. 

The Railroad Commission required every engineer to have his pocket watch inspected regularly and to submit a certificate stating its reliability to his supervisors. When there was only one track for trains barreling in both directions, being on time was a matter of life and death. As the Kipton wreck proved, an engineer's railroad watch being off by as little as four minutes could mean disaster.

The new standards dictated that a railroad pocket watch had to have at least 15 jewels. After 1886, the number of jewels increased. They also had to be accurate to within 30 seconds per week, as well as have a white dial—although the railroads allowed silvered dials until around 1910—with black Arabic numbers for each minute delineated; adjust to five positions, and be temperature compensated.

Although a pocket watch’s size, ranging from 0 to 23, didn’t refer to its width or length or casing but rather to the size of its movement, to meet railroad requirements, a watch's movement had to be either a size 16 (1 7/10 inches) or a size 18 (1 23/30inches).

Manufacturers sometimes broke the rules and made railroad watches with Roman numerals. The last two requirements were critical. As the early watchmakers discovered, not only could cold and heat cause a watch’s movement to slow or speed up, but so did the watch's position. Imagine a conductor trying to carry a watch in one position all the time, especially while working on a train. Railroad watches had to stand up to constant abuse from the jarring and swaying of early trains.

Contrary to common belief, there were many regulations in place before railroad officials commissioned Webb C. Ball to create a standard set of railroad watch qualifiers in the 1890’s. 

Before then, and until the entire railroad industry accepted Ball’s standards, different railroads had different standards for the watches their crews used. One line might have had a list of accepted makes and models while another might have only listed necessary features or timekeeping performance thresholds. This made evaluating older watches as railroad grade a difficult task, because a watch may have met the standards of one company but not another. 

As the rail industry grew in the United States, the number of active trains grew with it. In order to use a particular track efficiently, railroads had to create time schedules identifying when each section of that track was safe to use. The timekeeping accuracy of the engineer’s and conductor’s watches was crucial if two trains were moving in opposite directions. If one of the two engineers’ or conductors’ watches were keeping bad time, a collision could occur. Railroad watches became known as “standard” watches because they met a railroad’s standard of timekeeping.

Companies like Waltham, Elgin, and Hamilton made the “best” railroad watches after 1900. An important part of standard watch regulations included service intervals and testing, but there was also a list of features that almost all railroad watches shared. 

The most prominent feature of 1900’s railroad watches was their lever actuated setting mechanisms–commonly referred to as "lever-set.". Most watches were put in time-setting mode by pulling the crown, or winding knob, away from the watch, then pushing the crown back towards the watch to return to winding mode—referred to as "pendant-set."

A lever-set mechanism required the user to remove the bezel of the watch—the convex glass protecting the dial---and engage a lever to place the watch in setting mode. This tedious process of removing the bezel had a very important purpose. It ensured that the time on the watch was never accidentally changed by catching the winding knob on a pocket or any number of other unintentional situations.

Another important feature of railroad watches was their big, bold, black, Arabic numerals on highly contrasting white enamel dials with large bold hands. This feature made telling the time as clear and easy as possible while creating a distinctive and functional railroad watch design.

Mechanically speaking, almost all 1900’s railroad watches shared a number of performance and reliability enhancing features. Most had a fixed regulator to avoid timekeeping variation from impact, a double roller balance wheel to avoid going out of action, 19 or more jewels to reduce friction and increase consistency of the gear train, timekeeping adjustment in five or more positions to make sure the watch kept accurate time regardless of its orientation, and adjustment for temperature to ensure accuracy in a variety of climates. Many railroad watches had solid gold or gold plated gear trains and jewel settings to reduce the effects of magnetism as well as reduce tarnishing, and later watches had features such as magnetically resistant balance wheels.

Although there were many other fine pocket watches made in America, the quality of the workmanship made them second only to chronometers for being precise—they had to be.

To read more articles on antiques, please visit the Antiques Articles section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the over 30,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about "Coffee--The Brew of Life" in the 2023 Summer Edition, online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques and More Collection on Facebook.

A Question of Time and Age

QUESTION: I have inherited a very plain tall clock supposedly made in Philadelphia. It doesn’t seem to have any markings on it. How can I tell how old it is?

ANSWER: To tell the age of a tall-case clock, or grandfather clock as it’s more commonly known, you need to first look at the dial. The early ones at first showed 24-30 hours. Owners wound them at the end of that time by pulling the driving cord down.

In the earliest clocks—those dating from the 17th to early 18th centuries—the hour circle appears in a silvered ring with a doubled circle appearing within the numeral circle.

Many old clocks have only an hour hand. Some have both an hour and a minute hand. Even though clockmakers had used minute hands since 1670, most clocks, except the most expensive ones, didn’t have them. Early tall-case clockmakers gave their hands a fine finish and often made them the most decorative part of the clock. The hour hand was often the most elaborate and the second hand, if the clock had one, was sometimes long and graceful. Later, when clockmakers introduced white dials, the hour and minute hands became even more ornate and some even had a smaller second hand.

Originally, tall-case clockmakers made their dials of metal with a matt center circle. By the mid-17th century, they added ornamentation around the edge of this matted center, engraving birds or leaves to form a border showing the days of the month. They brightly burnished this date ring as well as the rings surrounding the winding holes. Silvered dials, containing no separate circle for the hours and minutes, appeared in 1750. Instead of a matted center circle, these dials featured an engraved overall pattern in the center circle. Many early tall-case clocks also had a small separate dial showing the days of the week.

Dials remained square until the beginning of the 18th century, at which time clockmakers introduced the arched dial. Dutch clockmakers found good use for this extra space, filling it with decorative figures and animated devices such as a see-saw or a shipping rolling at sea. They also added a moon dial, thereafter common on many tall-case clocks, which displayed the phases of the moon under the dial’s arch. English clockmakers, mostly in Yorkshire, went one step further, creating a globular rotating moon dial.

Clockmakers usually only made the works of tall-case clocks. They subcontracted the making of the cases to coffin makers, who used this as supplemental income when business was slow. During the second half of the 17th century, casemakers employed walnut to build mostly plain cases. The Dutch introduced marquetry to the fronts of the clock cases, using woods of different colors and grains.  Mahogany didn’t come into general use for tall-case clocks until about 1716. At first, casemakers imported it from Spain, then after that supply ran out, from Brazil.




Before 1730, the doors of most tall-case clocks were rectangular, but around that time casemakers included an arch in them to match the arched dials. The earliest clocks didn’t open with a door. Instead, the entire hood–the top part of the clock–slid backwards revealing the works.

To learn more about tall-case clocks, read “Grandfather Time” in #TheAntiquesAlmanac and also visit the Bowers Watch and Clock Repair Web site and read about the works of tall-case clocks in their clock section.

It's About Time

QUESTION: I have inherited a very plain tall clock made in Philadelphia. How can I tell how old it is?

ANSWER: To tell the age of a tall-case clock, or grandfather clock as it’s more commonly known, you need to first look at the dial. The early ones at first showed 24-30 hours. Owners wound them at the end of that time by pulling the driving cord down.

In the earliest clocks—those dating from the 17th to early 18th centuries—the hour circle appears in a silvered ring with a doubled circle appearing within the numeral circle.

Many old clocks have only an hour hand. Some have both an hour and a minute hand. Even though clockmakers had used minute hands since 1670, most clocks, except the most expensive ones, didn’t have them. Early tall-case clockmakers gave their hands a fine finish and often made them the most decorative part of the clock. The hour hand was often the most elaborate and the second hand, if the clock had one, was sometimes long and graceful. Later, when clockmakers introduced white dials, the hour and minute hands became even more ornate and some even had a smaller second hand.

Originally, tall-case clockmakers made their dials of metal with a matt center circle. By the mid-17th century, they added ornamentation around the edge of this matted center, engraving birds or leaves to form a border showing the days of the month. They brightly burnished this date ring as well as the rings surrounding the winding holes. Silvered dials, containing no separate circle for the hours and minutes, appeared in 1750. Instead of a matted center circle, these dials featured an engraved overall pattern in the center circle. Many early tall-case clocks also had a small separate dial showing the days of the week.

Dials remained square until the beginning of the 18th century, at which time clockmakers introduced the arched dial. Dutch clockmakers found good use for this extra space, filling it with decorative figures and animated devices such as a see-saw or a shipping rolling at sea. They also added a moon dial, thereafter common on many tall-case clocks, which displayed the phases of the moon under the dial’s arch. English clockmakers, mostly in Yorkshire, went one step further, creating a globular rotating moon dial.

Clockmakers usually only made the works of tall-case clocks. They subcontracted the making of the cases to coffin makers, who used this as supplemental income when business was slow. During the second half of the 17th century, casemakers employed walnut to build mostly plain cases. The Dutch introduced marquetry to the fronts of the clock cases, using woods of different colors and grains.  Mahogany didn’t come into general use for tall-case clocks until about 1716. At first, casemakers imported it from Spain, then after that supply ran out, from Brazil.

Before 1730, the doors of most tall-case clocks were rectangular, but around that time casemakers included an arch in them to match the arched dials. The earliest clocks didn’t open with a door. Instead, the entire hood–the top part of the clock–slid backwards revealing the works.

For more information, read “Grandfather Time” and also visit the Web site for Bowers Watch and Clock Repair and read about the works of tall-case clocks in their clock section.


To read more articles on antiques, please visit the Antiques Article section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 18,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about religious antiques in the special 2019 Winter Edition, "The Old West," online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques & More Collection on Facebook.

Promoting Through Time

QUESTION: I have an old clock with advertising for Jolly Tar Pastime Tobacco on it in raised letters. I’ve had the clock for a long time and never saw another one like it. Can you tell me anything about it?

ANSWER: You’re the lucky owner of a Baird advertising clock. You’ve no doubt seen pens and other items with printed advertising on them. But in the 1890s, a clock advertising a company was a novelty. Clocks promoted foods and beverages, household products, even medicines, such as Monells Teething Cordial for Children. They even advertised pet food like Clarke’s Patent Buffalo Meat Dog Cakes, endorsed by Queen Victoria, herself. Each clock says something different on it.

Born in Philadelphia in 1860, Edward Payson Baird went to work for the Seth Thomas Clock Company in 1879. In 1887, he left Seth Thomas to form his own company, the Baird Manufacturing Company, in Montreal, Canada,  to produce cases and doors for advertising clocks to house Seth Thomas movements. While he made his cases of pine or oak, he used papier-maché for the doors, with embossed letters around the clock face promoting the virtues of one product or another. Baird had numerous clients in the United States as well as in Canada and  Great Britain.

Baird used papier-maché for his clock doors because of the ready availability of wood pulp in Canada. By 1890, he moved his operation across the border to Plattsburgh, New York.  When economic circumstances forced him to close his Plattsburgh factory in 1896, Baird shifted his base of operations to Chicago, where he produced clocks with embossed, stamped tin advertisements. However, by that time interest in advertising clocks had begun to wane, so he concentrated his efforts on manufacturing parts for the fledgling telephone industry.

While some advertising brands, like Coca-Cola, are instantly recognizable and still exist today, many other products and brand names have long since disappeared. Baird clocks are the only clocks made from papier-maché that have advertising on them. Most resemble a figure 8. The top doors are 18 inches wide, while the bottom ones are 12 inches wide. While Baird clocks are 30½ long, Baird did make smaller 26-inch models. 

Baird also produced 18-inch-diameter gallery clocks. For the most part the dial on these clocks  measures 12 inches and the hands are straight, with a few exceptions. All Baird clocks have two doors unlike many other clocks produced at the time with only one door, giving access to the dial and pendulum.

A Baird clock in good working condition, with its original dial, glass, movement, and paint job, can sell for around $3,000. Some exceptional pieces sell for over twice that and higher. And well known brands, again like Coca-Cola, can sell for even more.

A Question of Time

QUESTION: I have inherited a very plain tall clock made in Philadelphia. How can I tell how old it is?

ANSWER: To tell the age of a tall-case clock, or grandfather clock as it’s more commonly known, you need to first look at the dial. The early ones at first showed 24-30 hours. Owners wound them at the end of that time by pulling the driving cord down.

In the earliest clocks—those dating from the 17th to early 18th centuries—the hour circle appears in a silvered ring with a doubled circle appearing within the numeral circle.

Many old clocks have only an hour hand. Some have both an hour and a minute hand. Even though clockmakers had used minute hands since 1670, most clocks, except the most expensive ones, didn’t have them. Early tall-case clockmakers gave their hands a fine finish and often made them the most decorative part of the clock. The hour hand was often the most elaborate and the second hand, if the clock had one, was sometimes long and graceful. Later, when clockmakers introduced white dials, the hour and minute hands became even more ornate and some even had a smaller second hand.

Originally, tall-case clockmakers made their dials of metal with a matt center circle. By the mid-17th century, they added ornamentation around the edge of this matted center, engraving birds or leaves to form a border showing the days of the month. They brightly burnished this date ring as well as the rings surrounding the winding holes. Silvered dials, containing no separate circle for the hours and minutes, appeared in 1750. Instead of a matted center circle, these dials featured an engraved overall pattern in the center circle. Many early tall-case clocks also had a small separate dial showing the days of the week.

Dials remained square until the beginning of the 18th century, at which time clockmakers introduced the arched dial. Dutch clockmakers found good use for this extra space, filling it with decorative figures and animated devices such as a see-saw or a shipping rolling at sea. They also added a moon dial, thereafter common on many tall-case clocks, which displayed the phases of the moon under the dial’s arch. English clockmakers, mostly in Yorkshire, went one step further, creating a globular rotating moon dial.

Clockmakers usually only made the works of tall-case clocks. They subcontracted the making of the cases to coffin makers, who used this as supplemental income when business was slow. During the second half of the 17th century, casemakers employed walnut to build mostly plain cases. The Dutch introduced marquetry to the fronts of the clock cases, using woods of different colors and grains.  Mahogany didn’t come into general use for tall-case clocks until about 1716. At first, casemakers imported it from Spain, then after that supply ran out, from Brazil.

Before 1730, the doors of most tall-case clocks were rectangular, but around that time casemakers included an arch in them to match the arched dials. The earliest clocks didn’t open with a door. Instead, the entire hood–the top part of the clock–slid backwards revealing the works.

For more information, read “Grandfather Time” and also visit the Web site for Bowers Watch and Clock Repair and read about the works of tall-case clocks in their clock section.