Who's for a Game of Cards?

 

QUESTION: Recently, while browsing though an antique shop, I came across two tables. Both had fold-over tops. One seemed like it was from the 18th century, the other from the Empire period of the 19th. The dealer unfolded the top of the older table to reveal a green felt cloth inlaid into it. He said that this was a card table. When he unfolded the top of the second table, it had no felt inlay and was plainly finished. He told me the second table was a tea table. I always thought they were both card tables. Can you tell me the difference and when card tables started to be used?

ANSWER: There’s a difference between the two tables, although subtle. Back in the 18th century, furniture was expensive as each piece was handcrafted to suit the customer. People woud have used their card tables as tea tables by just putting a tablescloth over it. But by the 1840s, furniture had begun to be at least partially machine-made, and manufacturers kept the cost down by making card tables plainer. 

Playing cards were probably invented during the Chinese Tang Dynasty around the 9th century as a result of the usage of woodblock printing. Playing cards became a diversion both in public houses and private homes. Early playing cards had neither suits nor numbers. Instead, they had instructions or forfeits for whoever drew them. Usually, playing cards revolved around drinking alcohol, especially in the public houses.

The earliest game involving cards occurred on July 17,1294 when the Ming Department of Punishments caught two gamblers, Yan Sengzhu and Zheng Pig-Dog, playing with paper cards. The Department confiscated the wood blocks used for printing the cards together with nine of the actual cards. By the 11th century, playing cards had spread throughout Asia and eventually made their way to Egypt. Playing cards probably came to Europe from the East, arriving first in either Italy or Spain.

By the early 18th century, specially made tables for playing cards began to appear all over England. The first card tables first appeared in the American Colonies around 1710. Card tables became symbols of wealth and the consequent expansion of leisure time and soon became a social necessity in every fashionable home. Without modern entertainment devices, about the only forms of evening entertainment was playing music, dancing, and of course, playing cards. 

Cabinetmakers constructed most of these imported English card tables of mahogany or walnut. Each had a hinged two-leaf top that, when open and supported on a swing leg, revealed an inner surface lined with leather, felt, or the coarse woolen cloth called baize. Since household lighting was usually inadequate for evening play, most of the tables had four turrets projecting from the corners to accommodate candlesticks. In addition, there were often “guinea pools” or “fishponds”—shallow dishlike depressions to hold money, dice, or counters—and, in Chippendale styles, a single drawer in which to keep the cards. The tables stood on graceful cabriole legs, meant to resemble a woman’s shapely calves, but their backs, unseen against the wall, remained unfinished.

Since so many of these tables were highly decorative and also bore their makers’ marks, they provide valuable evidence of the varieties of carving, inlay, veneer, and other detail used by the cabinetmakers, as well as of regional characteristics. Tables with bowed fronts were popular in Boston and Salem, and five- and six-legged examples appeared in New York.

Some people used card tables for purposes other than for playing cards. Unfortunately, tablecloths only covered over the fishponds, often causing accidents and breakage.

In Puritan New England and Quaker Philadelphia, as well as in the South, people bet huge sums on cockfights and horse races, on bull and bearbaiting. Doctors and lawyers would wager their fees at the card table, and the “devil’s prayer book”—a deck of playing cards—could be found everywhere.

From the beginning of the United States, gambling overpowered every effort to restrain it. By the late 18th century every fashionable home had a card table. Still, most households reserved the card table for recreational use.

In the upper-class 18th-century American home, ladies played cards at afternoon tea parties where guests might win or lose hundreds of dollars. In the evening, families would summon servants to bring the card table into the center of the drawing room after dinner, as card playing was a primary form of evening entertainment. Players became embroiled in spirited games of whist, a simpler foreunner of bridge, pokerlike brag, quadrille, or any of the several other games while spectators observed the action. 

When not in use, card tables in most households remained folded away to become consoles or side tables. Servants set card tables against the wall when not in use, sometimes with the upper half raised as a kind of ornamental backsplash.

After about 1840, card tables began to lose the felt inlaid on their surface. People still played cards but now these tables came into popular use as tea tables. With a smooth top, minus the fishponds and candlestick rests—indoor lighting had been much improved—it was now possible to place a tablecloth over the table without the fear of anything toppling due to the former depressions. In many cases, these table featured graceful rounded corners and were still being made of mahogany or walnut.

To read more articles on antiques, please visit the Antiques Articles section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the over 30,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about "The Age of Photography" in the 2023 Holiday Edition, online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques and More Collection on Facebook.

A Musical Chair for Musical Chairs

 

QUESTION: This summer while vacationing on Cape Cod, I spent some time antiquing. In one of the shops I discovered an unusual chair. It looked like a fancy side chair but the seat had hinges. When I lifted it up, I found a music box. The dealer told me that it was a Swiss Musical Chair, used in the game of musical chairs. What can you tell me about this chair? Where did it originate and who made it? 

ANSWER: While these chairs were popular with the wealthier set in the second half of the 19th and early 20th centuries, they don’t often appear in antique shops. Something like this is most often found in auctions or antique shows.

No one knows for sure who invented the game of musical chairs and when. But historians note that people have been playing it for centuries. Previously called “Trip to Jerusalem.” But when people began calling it Musical Chairs is also unknown. 

Trip to Jerusalem —known in German as “Reise Nach Jerusalem”—was a game played predominately in Germany. So why did people call the game “Trip to Jerusalem?” Some historians theorize that the Crusades inspired the name in the Middle Ages. They believe that the elimination of players who cannot find an empty seat at the end of each round compares to the losses suffered by the Crusaders as they battled the Muslims for control of Jerusalem. This would have made the game more relevant to players at the time. But as the centuries rolled on, that relevancy disappeared, so players started calling the game exactly what it was—a game of musical chairs.

Another less plausible theory, is that the immigration of Jews from the diaspora to the Land of Israel, called the Aliyah, inspired the game. During these trips, there was supposedly very limited spaces for Jews on the ships to the Land of Israel. This is supposedly depicted in the game by the number of chairs used. However, neither of these theories has ever been confirmed.

Musical chairs has always been a fun party game. The fact that it began with a "musical chair" seems lost in obscurity. The Swiss and Germans, known for their music boxes, found a novel way to insert one in the seat of an elaborately decorated chair. A hostess placed the chair among others in a circle. The game’s players walked around the circle while the music from the chair’s music box played. Whoever sat on the chair and stopped the music by engaging the switch that turned off the music box, had to leave the game. The last person to remain won.

Swiss and German craftsmen produced these chairs from the 1880s to the 1920s. They  used several kinds of wood, usually walnut plus some exotic varieties for inlays. They usually didn’t sign their chairs. Often, these chairs came in a set with an armchair and side chairs. 

The seat and seatback of these chairs featured intricately inlaid cartouches each depicting various images, including carved leaves and edelweiss, alpine chamois and deer. They placed the music box mechanism, made by another party, under the seat.

Woodcarving brought riches to the villages of Switzerland and the Black Forest region of Germany. It became all the fashion and no English traveler left these areas without having purchased some sort of woodcarving to take back home. As the tourist industry flourished and thrived, so did the carvers, selling their wares to the wealthy tourists.

Though the idea of a Grand Tour began in the 17th century, it wasn’t until the mid 19th century that it reached its peak. The wealthy believed the primary value of the Grand Tour lay in the exposure both to classical antiquity and the Renaissance, and to the aristocratic and fashionably polite society of the European continent.

The Grand Tour not only provided travelers with a cultural education but allowed those who could afford it the opportunity to buy things otherwise unavailable at home, such as the woodcarvings of Black Forest craftsmen. Grand Tourists would return with crates of art, books, pictures, sculpture, and items of culture, which would be displayed in libraries, cabinets, gardens, and drawing rooms.

This fashion had been set in motion by Queen Victoria's visit to the area in April 1868, and by her subsequent inspiration to build a Swiss chalet at Osborne House and fill it with Black Forest and Swiss carvings.

To read more articles on antiques, please visit the Antiques Articles section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the over 30,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about "Coffee--The Brew of Life" in the 2023 Summer Edition, online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques and More Collection on Facebook.

Simplicity and Comfort Rolled into One

 

QUESTION: Some time ago, I bought a simple chair at a country estate auction. I love that chair but know very little about it. Someone told me that my chair was Shaker. Since I didn’t know much about the Shakers, I couldn’t tell. It just looked like a simple country chair. What can you tell me about my chair? 

ANSWER: Your chair certainly looks like a Shaker chair. But you need to know a bit about the Shakers to know for sure. 

Mother Ann Lee, who led the Shakers to America in 1774, had enough to do to get her sect organized. She began with a community in Albany, New York, and sent out missionaries to establish Shaker communities elsewhere in New England. But it wasn’t until Mother Lee had died and another generation of leadership took over the Shakers that the idea of producing items for sale as a way of supporting the communities came to be.

The Shakers attracted skilled cabinetmakers and craftsmen to their ranks, so it was a natural to use their skills to produce furniture for the communities. By this time, the Shakers were totally self-sustaining. In the early 19th century, the sect began to attract large numbers of people, mostly those who were discontent with society in general or were out of work. The communities offered security and food and lodging to people who might otherwise not have had it.

To support all these people became a major problem. So the elders of each community came up with ways to produce items for sale. Some made chairs, others produced seeds, clothing, especially wool capes, or took in mending and such. Many members were very creative and invented unique items such  as the electric washing machine. They were extremely organized as well, so mass-producing items like chairs wasn’t a problem.  

Those who called themselves Shakers—officially the United Society of Believers in Christ’s Second Appearing—eventually numbered over 17,000. As the number of communities, referred to by the Shakers as “families,” their furniture making flourished. At their peak of production, the Shakers produced chairs at more than 50 locations. From their first base in New York, the Shakers expanded their communities to Connecticut, Massachusetts, New Hampshire, Ohio, Indiana, Kentucky, and even Florida.

The Shakers made many of their chairs along straight and simple lines to be light weight, strong, easy to clean, and comfortable, not every piece of furniture made by Shaker hands is a design masterpiece: Some pieces were poorly crafted. Some were beautifully crafted but poorly proportioned. And some exhibit such bare-bones functionalism that they’re awkward and ugly. Often they’re barely distinguishable from country furniture of the same time and place. Indeed, unscrupulous dealers and auctioneers often promote plain country pieces as Shaker and sell for several times more than they would otherwise bring.

For use in their communities, the Shakers created three kinds of chairs—dining chairs, side chairs and rocking chairs. They designed the dining chairs with low backs so that they would stand clear under the table when not in use. Or they could be hung on a peg rail against the wall while someone cleaned the floor. And to make sure the chair seats stayed clean, they hung them upside down. 

Side chairs came in several different styles. A sister’s chair had a lower seat than the brother’s chair. The dining chairs had two back slats while the side chairs usually had four, all of which were slightly slanted for extra comfort.

As early as the 1820s, many communities began mass producing chairs for both community use and for sale. They used the same designs from the 1840s to the early 1900s. Chairs produced in the early 19th century were mostly for community use. But during the last quart of the century, the Shakers heavily marketed their chairs to the “Outside World.”

The chairs that the Shakers designed to be sold to the public were lean and severe and produced in huge quantities that ended up on back porches and summer cottages across America. Their popularity led other manufacturers to copy their look, and these pseudo "Shaker" chairs appear in quantity at country auctions and small antiques shows. Each of the endless variety of styles has its own Shaker-designated model number. Most were originally stained dark brown, and slat-backs predominate. 

Even though the largest Shaker chair didn’t weigh over 10 pounds and the smallest less than 5 pounds, both could support the weight of the largest person. 

Each community made their chairs a bit different from those of other communities, changing or adding little details. And while they all began with the same design template, each community’s craftsmen added their own touches for their community. For instance, many people believe that all Shaker chairs have tiny acorn finials and arms that terminate in mushroom-shaped turnings. Not so. It’s possible to tell which community made which chair by the shape of the finial alone. The back slats were also often slightly different. The Number 7 rockers, for example, have mushroom arms, four slats, and a shawl rail connecting the backposts that replaces the more common finials. The Shakers often attached a decal identifying the piece as Shaker to the back of a slat or leg. But pieces meant solely for use within the Shaker communities didn’t have decals. 

During the second half of the 19th century, the Shakers painted some of their chairs and woven brightly colored tapes into their seats. Often they combined colors, such as red and black and tan and maroon. Most colors, however, had more conservative names like Trustee Brown, Meetinghouse Blue, and Ministry Green.

In addition to the colorful tape, the Shakers also used cane, rush, and woven splint for their seats.

The woods used in chair construction varied according to the regional supply. But it was always of top quality and well cured. The most commonly used woods included walnut, cherry, butternut, and birds-eye maple, as well as pine and fruitwood if the others weren’t available.

Although for years Shaker chairs never sold for more than $500, now even the most common three-slat rockers bring $600 to $800 or more. Some even go as high as $1,700 to $2,200. 

Pieces from Kentucky, Ohio, and Indiana—often less austere, less "Shaker-looking" than their eastern counterparts—often have a Victorian feel and sometimes resemble local country furniture even more closely than classic eastern designs. .

The quality of many reproductions of Shaker chairs, made using the same tools and techniques, is often so good that they sell for as much as the originals.

For over a century, the creation of Shaker chairs was but a simple fulfilling of the motto of their faith, “Hands to work and hearts to God.”

To read more articles on antiques, please visit the Antiques Articles section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the over 30,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about art glass in the 2022 Summer Edition, with the theme "Splendor in the Glass," online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques and More Collection on Facebook.

Preservation vs. Conservation

QUESTION: I have several pieces of antique furniture that need some tender loving care, but I’m not sure how to go about it. Can you explain the difference between preservation and conservation? And can you give me some tips on how I can take care of my pieces?


ANSWER: Preservation involves keeping an object from destruction and seeing to it that it’s not irreversibly altered or changed. In conservation, on the other had, the goal is to preserve the maximum amount of the original material, in as unaltered a condition as possible.

Furniture conservation and restoration can be divided into two general areas—structure and finish. Structure generally relates to wood---solid, joined, and veneered. The finish of furniture can be painted or varnished.



Antiques restoration can be an arduous process if the goal is complete authenticity. This is particularly true for museum conservators. For them, authentic material is the actual original material of the object. For example, a chair with its original upholstery, even if it is faded and shredded, is authentic for the conservator and possesses historic value even though it may not be exhibitable. The same chair can be "restored" and looking as it did when new, with replacement fabric copied from the original weave and colors, and upholstered according to the known design of that particular piece of furniture.

Some pieces of furniture, especially those constructed of harder woods, such as walnut, mahogany, maple, oak, or cherry, may only need to have their surface finish preserved. In the case of furniture made of these woods, there may be enough of the original finish left to restore the piece rather than refinish it.

Before doing anything, study your piece. Is the finish pretty much intact? Does the piece have a nice patina? Is the piece more than 100 years old? If you answered yes to even one of these questions, then you should do your best to preserve the original finish of your piece.

The first step in preservation is cleaning. Furniture gets dirty, even grimy over time. Before you can apply a new finish, you need to get rid of all the accumulated dirt and grease that often make it difficult to tell what kind of wood the piece of furniture is made of. Grime can also hide the fine lines of inlay and marquetry. Believe it or not, using lemon oil, a popular furniture polish, can do more harm than good. Since its made of a light petroleum oil and some paraffin wax, the wood doesn’t absorb it. Instead, it acts as a surface dust catcher.

One of the best products for cleaning wood, especially furniture, is Murphy’s Oil Soap. Today, it’s also in a spray bottle, but in case you can’t find it that way, you can make your own cleaning solution by mixing a capful of Murphy’s in a spray bottle of water. For this, you can use any empty spray cleaner bottle, as long as you wash it out thoroughly first. Since water will loosen any glued joint, and also tends to raise the grain of the wood, you don’t’ want to use very much. An old washcloth will do quite well for cleaning.

Spray the Murphy’s on a damp washcloth and then rub it on the surface of the furniture. Rinse the cloth when it gets to dirty. Have a second wet, but wrung out, washcloth ready to wipe off the Murphy’s Oil solution, wringing the cloth nearly dry after every few wipes. You can also use a green scruby cloth, sold in Dollar Stores, if there’s hard to remove grime. A stiff-bristle brush will allow you to get the dirt out of carved and turned areas. The secret is to clean only a small area at a time–one leg of a chair, one part of a chest, and so on. After you clean an area, wipe it dry with an old face towel. Be sure to wash out all your cloths or use others as you progress, especially on a large piece of furniture. After you have finished cleaning your piece of furniture, give it a final wipe with a clean cotton rag and set it aside to dry for 24 hours.

All this cleaning may cause joints to loosen, so be sure to check the structural integrity of your piece before applying a new finish. If joints need to be tightened or reglued, do so before applying a new finish.

Now you’re ready to apply a new finish. You can either use plain tung oil or a product like Minwax® Water-Based WoodSheen® which is a water-soluble mixture of furniture finish and stain that comes in six colors. For a piece that’s got lots of scratches or marks, it’s best to choose a stain color that complements the wood’s original finish.

The final step is polishing the entire piece using a prepared wax like Minwax, which comes in light and dark varieties. Obviously, use the light for woods like oak or cherry and the dark for woods like walnut or mahogany. Apply the wax with a piece of soft cotton cloth like an old athletic sock and after 30 minutes, polish the surface with an old face towel. One coat should do it, but for tabletops, apply two coats of wax.

Rub off the first coat with 0000 steel wool, then apply the second and polish with the towel. The more coats of wax you apply, the more water resistant the top will become. A light polishing once or twice a year will keep your piece in great condition.

There are no short cuts or time savers to this entire process. The work can be slow and at times tedious, but the results are worth it.

To read more articles on antiques, please visit the Antiques Article section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 24,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about antique clocks in the Fall 2019 Edition, "It's That Time Again," online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques & More Collection on Facebook.

A Question of Time and Age

QUESTION: I have inherited a very plain tall clock supposedly made in Philadelphia. It doesn’t seem to have any markings on it. How can I tell how old it is?

ANSWER: To tell the age of a tall-case clock, or grandfather clock as it’s more commonly known, you need to first look at the dial. The early ones at first showed 24-30 hours. Owners wound them at the end of that time by pulling the driving cord down.

In the earliest clocks—those dating from the 17th to early 18th centuries—the hour circle appears in a silvered ring with a doubled circle appearing within the numeral circle.

Many old clocks have only an hour hand. Some have both an hour and a minute hand. Even though clockmakers had used minute hands since 1670, most clocks, except the most expensive ones, didn’t have them. Early tall-case clockmakers gave their hands a fine finish and often made them the most decorative part of the clock. The hour hand was often the most elaborate and the second hand, if the clock had one, was sometimes long and graceful. Later, when clockmakers introduced white dials, the hour and minute hands became even more ornate and some even had a smaller second hand.

Originally, tall-case clockmakers made their dials of metal with a matt center circle. By the mid-17th century, they added ornamentation around the edge of this matted center, engraving birds or leaves to form a border showing the days of the month. They brightly burnished this date ring as well as the rings surrounding the winding holes. Silvered dials, containing no separate circle for the hours and minutes, appeared in 1750. Instead of a matted center circle, these dials featured an engraved overall pattern in the center circle. Many early tall-case clocks also had a small separate dial showing the days of the week.

Dials remained square until the beginning of the 18th century, at which time clockmakers introduced the arched dial. Dutch clockmakers found good use for this extra space, filling it with decorative figures and animated devices such as a see-saw or a shipping rolling at sea. They also added a moon dial, thereafter common on many tall-case clocks, which displayed the phases of the moon under the dial’s arch. English clockmakers, mostly in Yorkshire, went one step further, creating a globular rotating moon dial.

Clockmakers usually only made the works of tall-case clocks. They subcontracted the making of the cases to coffin makers, who used this as supplemental income when business was slow. During the second half of the 17th century, casemakers employed walnut to build mostly plain cases. The Dutch introduced marquetry to the fronts of the clock cases, using woods of different colors and grains.  Mahogany didn’t come into general use for tall-case clocks until about 1716. At first, casemakers imported it from Spain, then after that supply ran out, from Brazil.




Before 1730, the doors of most tall-case clocks were rectangular, but around that time casemakers included an arch in them to match the arched dials. The earliest clocks didn’t open with a door. Instead, the entire hood–the top part of the clock–slid backwards revealing the works.

To learn more about tall-case clocks, read “Grandfather Time” in #TheAntiquesAlmanac and also visit the Bowers Watch and Clock Repair Web site and read about the works of tall-case clocks in their clock section.

Somewhere to Dream

QUESTION: My husband and recently purchased an antique four-poster bed from around 1810.  The dealer called it a tester bed. It originally had a canopy which needs to be replaced. Can you tell me what a tester is and something about the origins of this type of bed?

ANSWER: Initially the wooden frame of the bed was far less important that the trappings of textiles that surrounded it. Most any reference to a bed centuries ago actually meant the mattress and whatever cloth materials people piled upon it.

During medieval times there was no particular room set aside for sleeping quarters, thus the bed became almost a room within the household. Some of the more elaborate bedsteads had both a room and sliding panel walls. Occupants could climb inside and stuff them-selves off from the rest of the chilly and drafty residence.

Gradually, heavy curtains replaced the side panels of the "bedroom," but the basic roof remained. The solid roof, known as a tester, retained the name even though the roof covering eventually became one of cloth and curtains as the sides had been.

Basically, a bedstead and two posts supported the roof of these early beds. Over the decades makers adopted a style which incorporated four posts which supported the full tester canopy.

Early in the 18th century, during the Queen Anne period, wealthy homeowners often covered their four-poster beds with velvet and other textiles so extensively that they obscured the basic woodwork. Cabinetmakers used back panels less and less. As the century progressed, the rear posts remained covered with curtains while the front posts became more visible. As a consequence, bed makers carved and decorated the front posts more elaborately.

Some of the most impressive four-poster  beds reached heights of eight feet or more, complete with a sweeping array of curtains and canopy. Cabinetmakers made sturdy frames from mahogany or walnut. People could close panels of curtains at night for more warmth and security. Matching coverlets and bases then totally enveloped the grand bed in a sea of cloth.



Wealthy homeowners continued to import fabric for their bed coverings from Europe in the 1750s and 1760s. But with the increase in leisure activities and attention to developing social graces that characterized the time, fancy needlework done by women and school girls often supplied the decorative detail.

By the dawn of the 18th century, the finest bed available was the Chippendale bed. The Chippendale and those similar in style displayed predominantly high foot posts which were handsomely carved and ended elegantly with ball and claw feet. By contrast, cabinetmakers sometimes didn’t carve the head posts and instead left them plain to be extensively decorated by fabrics. Elaborate decorating of the beds gradually increased as owners opted for serpentine headboards and reeled posts in lieu of additional drapes.

By the 1800s, the lavish use of fabrics on beds had diminished considerably and the wood itself had more of a prominent role in the overall design. Almost without exception, cabinetmakers carved or decorated posts. In addition, homeowners began placing their beds in separate rooms designed for sleeping, usually on the second floor of their houses, instead of in parlors or various other locations in their homes.  .

The rise of the Empire period in the 1820s had an impact on a vast assortment of furniture, including the bed. Scrolled headboards were very fashionable, and posts were decorated with acanthus leaves and detailed beading. Mahogany remained one of the most popular woods of choice.

It wasn’t unusual for the well established to spend more for their bed furnishings than on the actual wood structure, itself. They preferred bright colors over white and added  fine linen-like textiles in shades of red, blue, yellow and green. Many also used generous amounts of silk and lace, along with woolen cloths.

To read more articles on antiques, please visit the Antiques Article section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 18,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about religious antiques in the special 2019 Winter Edition, "The Old West," online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques & More Collection on Facebook.

50 Shades of Veneer

QUESTION: At several antiques shows I’ve attended recently, I noticed some beautifully decorated veneered boxes from the 18th century. At one of them, I also saw a hall table with a top decorated with a floral marquetry bouquet.  I know nothing about how veneering is done, nor do I know how it originated. What can you tell me about this intricate work?

ANSWER: Today, the art of veneered marquetry and veneer decoration is almost non-existent. But back in the 17th,18th and early 19th centuries, it was all the rage.

Early furniture makers recognized and appreciated beautiful woods and wood grains for their beauty. Veneering, the process of gluing thinly cut layers of precious wood to surfaces of less exotic wood, goes back to ancient times and became popular during the Renaissance, when inlay designs were common forms of furniture decoration.

But there was a problem early on with cutting large enough slabs of wood to the desired thinness in order to cover entire surfaces with single sheets of the more precious wood. So cabinetmakers cut small pieces of wood and glued them to the carcass of a piece of furniture in patterns and designs that took advantage of the beauty of the wood grain and variations in color.

By the 17th century, veneering became an art, and the decorative use of thin sheets of wood could be found on many examples of European furniture. The French were the style-setters in marquetry inlay, and British and other European craftsmen soon followed suit.

There were two advantages to using veneers. The first reduced the cost of a piece of furniture or a box by applying an exotic and expensive wood to a less expensive domestic wood. The second advantage was that the tensile strength of the surface of a piece could be increased many times when the cabinetmaker laid a veneer cross grain to the under piece of wood. The layer of glue between the two surfaces also added to the strength of the finished piece.

The aesthetic advantages of the use of veneers in the decoration of cabinetry  increased, also. The cabinetmakers, using thinly cut sheets of the same piece of wood, could repeat the grainings and markings in order to form interesting patterns. This use of the natural design in wood required artistry as well as craftsmanship. By using veneers judiciously, cabinetmakers could inlay designs and decorations of different kinds and colors of wood, thus producing interesting motifs and styles.

Before the 19th century, specially trained veneer cutters, skilled in slicing the layers of expensive wood to uniform thickness, cut veneers by hand. They then sold these sheets to furniture makers and box makers who used them in decorating the many kinds and styles of decorative furniture and boxes that developed in the 17th and 18th centuries.

At the beginning of the19th century a steam-driven saw, registered in London, that made it cheaper, faster, and easier to cut large, thin, uniform slices of wood to be used for veneers. After the invention of the special saw, wood could be cut in many different ways to take advantage of the variations in grainings.



The different designs that could be obtained in veneered wood depended on the type of wood used and the way in which the log was cut. The earliest methods of cutting veneers by hand produced only vertically cut grains. This vertical slicing achieved a pattern which was circular and was known as "oystering." Other types of graining commonly used in the 19th century were "crotch," cut from the area of the tree where two limbs fork out, the "burl," a growth on the tree trunk and a particularly attractive gnarled design, and "bird's-eye," which was formed by the deep growth of buds most commonly found on the maple tree. Many other patterns could be obtained by the expert cutting of the wood in different cross sections and the employment of the saw in cutting circular sections around the log.

Woods often used in producing veneers were chestnut, poplar, walnut, elm, birch, rosewood, ebony, satinwood, sandalwood, sycamore, box, yew, olive, pear, teak, tulipwood, laurel, and many other similar exotic woods. Mahogany was and still is the most popular veneer wood. It was strong and hard and had figurations in the various cuts of its grain that were unmatchable for their beauty. Mahogany also takes a high polish extremely well.

A large variety of boxes were made of veneered wood in the 19th century. British box makers, especially, produced a great many veneered boxes. Often, they made elaborate boxes to protect valuables against damage, and more often, theft. Sometimes, they made elegant boxes simply as a means of displaying the contents to its best advantage.


To read more articles on antiques, please visit the Antiques Article section of my Web site.  And to stay up to the minute on antiques and collectibles, please join the other 18,000 readers by following my free online magazine, #TheAntiquesAlmanac. Learn more about religious antiques in the special 2019 Winter Edition, "The Old West," online now. And to read daily posts about unique objects from the past and their histories, like the #Antiques & More Collection on Facebook.

Asleep in Luxury

QUESTION: My mother-in-law, who is 97, has just moved into a retirement home. Her Aunt Margaret was married to Charles Tuckett, the son of Charles Elias Tuckett, founder of Tuckett Tobacco and one time mayor of Hamilton, Ontario. Charles inherited the original Tuckett Estate and when he passed away Margaret was left owning it. Charles and Margaret had one child but the child died. When Margaret died her family inherited the estate. My mother-in-law inherited a lot of the furniture, but I haven’t found  much help regarding the manufacturer and value. Can you help me?

ANSWER: Your mother-in-law now owns two fine pieces of
furniture. Not only are they of massive scale, but the carving on them looks to be made by hand, something that wasn’t common in the late 19th century when most factories made manufactured most furniture.

These two pieces together make up a ‘bedchamber suite,” a more formal version of bedroom suite. Earlier suites consisted of just two pieces—a bed, commonly referred to as a “bedstead” and a dressing case, what most people call a dresser. Both came in all shapes and sizes and in one of seven different major revival styles. This suite is a fine example of the massive Renaissance Revival style, preferred by wealthy Americans. Later on, a second type of suite appeared, one with a bedstead, washstand, and bureau. These were smaller in scale—ideal for middle class homes and Victorian cottages—and less ornate and expensive than their bigger cousins. The concept of selling furniture “en suite” was novel in the 1880s and 1890s. Today, we this for granted.

Not only did the size show off the wealth of the suite’s owners, it also fit the enormous rooms with 12-foot high ceilings common in Victorian Italianate mansions of the time.

Suites with dressing cases from the Victorian period were more expensive than the bureau type, and more elegant as well. Sometimes their tall mirrors seemed to extend from floor to ceiling and had ornately carved frames that featured small bracket shelves for candle-holders or small lamps. Drawers varied in number and size. What people now describe as a well or step-down generally separated the parallel series of drawers. Cabinetmakers treated all three levels alike, topping them with either wood or marble. Some pieces had full-width drawers at the bottom of the well. Sometimes, the mid-section below the looking glass reached down to the floor, but this wasn’t common. To achieve individuality, customers could order their own mirror frame, and select from 16 different carved drawer pulls.

In the 19th century, the word "toilet" referred to personal grooming, thus a mirror became a  toilet or plate. An oval "plate" is now called a wishbone mirror, since the frame in which it is suspended is shaped roughly like a fowl's wishbone.

During the 1870s, people referred to the two small drawers that sit across from each other on the top of a bureau as decks. Today, they’ve become known as handkerchief boxes. Much less common were the petite boxes with hinged lift lids that sat on top of the dresser.

A projection front refers to the part of a dresser that hangs out over the base. A drawer or two may project or overhang the others. Slipper drawers had no handles and appeared to be the apron on a dresser. Not surprisingly, owners stored their slippers in them. Some dressers even had hidden compartments for jewelry.

This particular dressing case has all the features of the American Renaissance Revival style and then some. Not only does it have the small drawers, but also smaller cabinets with carved fronts with what look to be magnolia flowers. How magnolia flowers got to be on a piece of furniture made in Canada is a mystery. Burl walnut veneer decorates the fronts of the larger panels. And both the dresser case and the bedstead feature a large carved medallion with a dove of peace.

It’s believed that this bedchamber suite was originally in The Towers, an Italianate mansion built by George Elias in the 1870s, the second manion on his property. Today, renamed The Scottish Rite, it’s the home of a Masonic Lodge. When George Elias had The Towers built, he commissioned a local cabinetmaker, Joseph Hoodless, to not only create the mansion’s fine woodwork, but also some custom pieces of furniture, including this bedchamber suite. At the time, Hoodless had the reputation of being the finest furniture maker of his time. One of his bedchamber suites won gold metal at the Toronto Exhibition.

Because this is so customized a piece, value is hard to determine. Similar bedchamber suites have sold for upwards of $10,000 or more.

To learn more about Victorian Revival furniture, read "The Victorian Era---An Age of Revivals."